#Hercules table saw dado insert portable#
We switched out the discontinued DeWalt DWE7480, a portable 10-inch model, for the new DeWalt DWE7485 - an 8-1/4-inch option that, despite having a smaller maximum cut depth than the DWE7480, features a slightly better bevel capacity and a no-load speed of 5,800 RPM, compared to the DWE7480’s 4,800.
#Hercules table saw dado insert series#
30 in.A series of upgraded models released over the past year made for a fairly busy round of updates, with half of our previous selections being replaced. For the price and performance, this budget-friendly saw should appeal to both DIYers and entry-level Pros. We like the fold-and-roll stand overall, but watch that the curved leg doesn’t obstruct a pathway.
The narrow base and light weight make it a little wobbly with larger stock or sheet goods. The saw also has plenty of power and it’s hard to beat the maneuverability. The fence clamping system now exhibits a much more confident mechanism.
You get a big weight reduction for more portability. Kobalt has made some nice improvements to this table saw. DeWalt DW745S compact job site table saw (fixed stand): $302.32.Here’s a look at some budget-friendly competitors: The regular price for the KT10152 sits at $329. We’ve seen recent deals on the Kobalt portable table saw that really make it a bargain. It’s not a deal-breaker but you should be wary of it when locating the saw in your workspace. But because it curves upward and further out into the workspace, it becomes quite a trip hazard and shin buster (we’re speaking from experience!). Given what we just said about the width of the legs, it might seem contradictory to gripe about the curved leg sticking too far out. We did, however, notice a bit of an issue once we set up the saw. The lightweight Kobalt portable table saw works hand-in-hand with the included fold-and-roll stand to make it very maneuverable. Some Pros will opt to use track saws for this application, however the budget-friendly KT10152 comes in at nearly half the price. As you push sheet goods through the blade, the stand doesn’t supply enough stability where you need it the most. The fold-and-roll stand, which we discuss below, is wider than the saw perpendicular to the blade but not parallel to it. Sheet goods make it a bit too wobbly unless you’ve got some capable help or outfeed support. The lower weight on this table saw actually works as a disadvantage in this case. Smaller saws tend to lend themselves to being top-heavy. It’ll be no surprise that cutting sheet goods on the Kobalt KT10152 portable table saw (or any jobsite saw) isn’t ideal. And the impressive stock blade is still in good shape after all our work. We ripped plenty of 2x material and even cement board. The Kobalt portable table saw’s carbide-tipped blade and 15-amp motor easily cut through everything we had. The sliding mechanism actually feels like it belongs on a more expensive saw-it’s very smooth! Our crew found the fence easy to square and-more importantly-it stayed square. A good fence will properly align itself from the front. It had two independent locks, but you could just as easily lock it out of square. Kobalt Tools also added yellow pins on the slide that register the fence square.Ī common gripe about the KT1015 was its tough-to-square fence. Perhaps the most helpful change, though, is a redesign of the sliding fence from a double latch to a single latch. The right rip capacity is the same at 30 inches but the left is up to 17 inches from 14. That’s a big advantage for portability but also a disadvantage for certain applications. At just 65 pounds, it drops 13 pounds from the KT1015. However, if you moved both around, you’d find the new model to be much more nimble. What’s the Difference Between the Kobalt KT10152 and KT1015?Įxcept for its color scheme, you’d be hard-pressed to quickly pinpoint the differences between this Kobalt Portable Table Saw (model KT10152) and its predecessor, the KT1015 we compared in our jobsite table saw head-to-head. Altogether, this new Kobalt job site table saw is a capable budget performer that shows Kobalt is committed to quick improvements. Finally, the curved legs extend pretty far past the edge of the table creating a trip hazard/shin buster. It’s got ample power to cut 2x, cement board, and more. The saw’s low weight and smaller table surface make it ill-suited for ripping sheet goods.
We found it much easier to set and adjust-almost like a premium feature on this budget-friendly saw. Perhaps the most significant change is in the sliding fence-a common gripe about the last version-that now has one latch instead of two. RecommendationKobalt significantly reduced the weight of this saw from its predecessor and added three inches of rip capacity.
0 kommentar(er)
